Get a quote
T-05 · free calculator

Roof Pitch Calculator

Enter the rise and run of the roof, or the angle you already know, to get the pitch in degrees, percent and as a ratio, plus the pitch factor, rafter length and slope area.

  • Cost: free, no sign-up
  • Works on: phone and computer
  • Then: get quotes in one step
Stack of charcoal natural slate roof tiles beside a half-finished pitched roof on a Highveld house in morning light
Stack of charcoal natural slate roof tiles beside a half-finished pitched roof on a Highveld house in morning light

Roof pitch calculator

Your numbers

Pitch
– degrees
Ratio
–
Slope
– %
Rise per metre
– mm
Pitch factor
–
Rafter length
– m
Roof slope area
– m²
Suits
–

Estimates only. Check quantities with your supplier or installer before you buy.

Measure up

Know the size? Enter it and we add the area to your request. Skip it if you are not sure.

0 m² to order

Roofs, walls and steps: measure each face and add them up, or type the total in the form.

Get a free quote

Tell us what you need and where. A slate supplier, tiler, cladding installer or roofer who works in your area quotes you directly.

Measure sheetMS-07405
Tick what applies (optional)

Free and no obligation. By sending you agree that we may share your request with a suitable supplier or installer. See our privacy policy.

Free roof pitch calculator: enter the rise and run or the angle, and get the pitch in degrees, percent and ratio, the pitch factor, rafter length, roof area and which coverings suit it.

Rise, run and pitch

The run is the horizontal distance from the outside of the wall plate to the point under the ridge, normally half the span of a simple gable roof. The rise is the height from the wall plate to the ridge. The pitch in degrees is the arctangent of rise ÷ run: a rise of 2.5 m over a run of 4.3 m is about 30°.

The pitch factor (1 ÷ cos pitch) converts a flat plan area to the actual sloping area of the roof, which is what roofing materials are ordered by. The rafter length is the run × pitch factor, plus the overhang.

Measuring the pitch of an existing roof

  • In the roof space: hold a spirit level horizontally against a rafter, measure 1 m along it and measure straight up to the underside of the rafter. That height in metres is the rise per metre; enter run = 1.
  • From the gable end: measure the height of the ridge above the ceiling level and half the width of the house.
  • With a phone: many phones have a level or angle function that reads the slope directly off a rafter or the bargeboard.
  • From plans: the architect's sections usually state the pitch in degrees.

Which coverings suit which pitch

As a general guide: IBR and corrugated sheeting from about 5°, concrete roof tiles from about 17.5° (some profiles allow 15°), clay tiles and fibre-cement slates from about 20–25°, and natural slate from about 20°, with larger slates and headlap at the low end. Thatch needs 45° or more. Always check the minimum pitch in the manufacturer's guide for the exact product.

Frequently asked questions

How do I convert a roof pitch ratio to degrees?
Divide the rise by the run and take the arctangent. A 1:2 pitch (1 up for every 2 across) is arctan(0.5) = 26.6°. A 1:1 pitch is 45°.
What is a normal roof pitch in South Africa?
Tiled roofs on houses are commonly between 17.5° and 30°. Older homes with natural slate roofs are often steeper, 35° to 45°, while sheeted roofs can be as low as 5°.
What is the pitch factor?
It is the number you multiply the plan area by to get the true sloping area of the roof: 1 ÷ cos(pitch). It is 1.035 at 15°, 1.064 at 20°, 1.155 at 30° and 1.414 at 45°.

Products and services this helps with

More calculators and guides

Get a free quote